DM9000
isa 至 ethernet mac 控制 和 整体的 10/100 phy
18 最终
版本: dm9000-ds-f02
六月 26, 2002
6.17 multicast 地址 寄存器 ( 16h~1dh )
位 名字 Default 描述
7:0 MAB7 x,rw multicast 地址 字节 7 (1dh)
7:0 MAB6 x,rw multicast 地址 字节 6 (1ch)
7:0 MAB5 x,rw multicast 地址 字节 5 (1bh)
7:0 MAB4 x,rw multicast 地址 字节 4 (1ah)
7:0 MAB3 x,rw multicast 地址 字节 3 (19h)
7:0 MAB2 x,rw multicast 地址 字节 2 (18h)
7:0 MAB1 x,rw multicast 地址 字节 1 (17h)
7:0 MAB0 x,rw multicast 地址 字节 0 (16h)
6.18 一般 目的 控制 寄存器 ( 1eh )
位 名字 Default 描述
7:4 保留 0,ro 保留
3:0 gep_cntl 0001,rw 一般 目的 控制
定义 这 输入/输出 方向 的 一般 目的 寄存器
当 一个 位 是 设置 1, 这 方向 的 correspondent 位 的 一般 目的 寄存器
是 输出. gpio0 default 是 输出 为 power_向下 函数. 其它 defaults 是
输入
6.19 一般 目的 寄存器 ( 1fh )
位 名字 Default 描述
7:4 保留 0,ro 保留
3:1 gepio3-1 0,rw 一般 目的
当 这 correspondent 位 的 一般 目的 控制 寄存器 是 1, 这 值 的
这 位 是 反映 至 管脚 gepio3-1
当 这 correspondent 位 的 一般 目的 控制 寄存器 是 0, 这 值 的
这 位 至 是 读 是 反映 从 correspondent 管脚 的 gepio3-1
这 gepios 是 编排 至 管脚 gepio3 至 gepio1 各自
0 GEPIO0 1,rw 一般 目的
当 这 correspondent 位 的 一般 目的 控制 寄存器 是 1, 这 值 的
这 位 是 这 输出 至 管脚 gepio0
当 这 correspondent 位 的 一般 目的 控制 寄存器 是 0, 这 值 的
这 位 至 是 读 是 反映 从 管脚 gepio0. gepio0 default 输出 1 至
电源_向下 内部的 phy. 驱动器 needs 至 clear 这个 电源_down 信号
用 writing “0” 当 它 wants phy 至 是 起作用的. 这个 default 值 能 是
编写程序 用 可擦可编程只读存储器. 请 谈及 至 这 可擦可编程只读存储器 描述
6.20 tx sram 读 pointer 地址 寄存器 (22h~23h)
位 名字 Default 描述
7:0 TRPAH 00h,ro tx sram 读 pointer 地址 高 字节 (23h)
7:0 TRPAL 00h.ro tx sram 读 pointer 地址 低 字节 (22h)
6.21 rx sram 写 pointer 地址 寄存器 (24h~25h)
位 名字 Default 描述
7:0 RWPAH 0ch,ro rx sram write pointer 地址 高 字节 (25h)
7:0 RWPAL 04h.ro rx sram write pointer 地址 低 字节 (24h)