25 S29AL016M
s29al016m_00a4 april 21, 2004
这 重置 command 将 是 写 在 这 sequence 循环 在 一个 autoselect
command sequence. once 在 这 autoselect 模式, 这 重置 command
必须
是
写 至 返回 至 读 排列 数据 (也 应用 至 autoselect 在 擦掉
suspend).
如果 dq5 变得 高 在 一个 程序 或者 擦掉 运作, writing 这 重置 command
returns 这 设备 至 读 排列 数据 (也 应用 在 擦掉 suspend).
autoselect command sequence
这 autoselect command sequence 准许 这 host 系统 至 进入 这 manu-
facturer 和 设备 代号, 和 决定 whether 或者 不 一个 sector 是 保护.
Ta bl e s10–11显示 这 地址 和 数据 (所需的)东西. 这个 方法 是 一个 改变
-
native 至 那 显示 在 表格4, 这个 是 将 为 prom programmers 和
需要 v
ID
在 地址 位 a9.
这 autoselect command sequence 是 initiated 用 writing 二 unlock 循环, fol-
lowed 用 这 autoselect command. 这 设备 然后 enters 这 autoselect 模式,
和 这 系统 将 读 在 任何 地址 任何 号码 的 时间, 没有 初始的
另一 command sequence.
一个 读 循环 在 地址 xx00h retrieves 这 生产者 代号. 一个 读 循环 在
地址 xx01h returns 这 设备 代号. 一个 读 循环 containing 一个 sector 地址
(sa) 和 这 地址 xx02h 在 文字 模式 (或者 xx04h 在 字节 模式) returns
xx01h 如果 th在 秒至r 是 protected, 或者 00h 如果它 是unprotected. 谈及 至 tables2和
3为 有效的 sector 地址.
这 系统 必须 写 这 重置 command 至exit 这 autoselect 模式 和 返回
至 读 排列 数据.
文字/字节 程序 command sequence
这 系统 将 程序 这 设备 用 文字 或者 字节, 取决于 在 这 状态
的 这 byte# 管脚. 程序编制 是 一个 四-总线-循环 运作. 这 程序
command sequence 是 initiated 用 writing 二 unlock 写 循环, followed 用
这 程序 设置-向上 command. 这 程序 地址 和 数据 是 写 next,
这个 在 转变 initiate 这 embedded 程序 algorithm. 这 系统 是
不
re
-
quired 至 提供 更远 控制 或者 timings. 这 设备 automatically
发生 这 程序 脉冲 和 核实 这 编写程序 cell 余裕. tables
10–11显示 这 地址 和 数据 (所需的)东西 为 这 程序 command se
-
quence.
便条 那 这 secsi sector, autoselect, 和 cfi 功能 是
无法得到 当 一个 程序 运作 是 在 progress.
当 这 embedded 程序 algorithm 是 完全, 这 设备 然后 returns 至
读 排列 数据 和 地址 是 非 变长 latched. 这 系统 能 deter
-
mine 这 状态 的 这 程序 运作 用 使用 dq7, dq6, 或者 ry/by#. 看
“write 运作 status”为 信息 在 这些 状态 位.
任何 commands 写 至 这 设备 在 这 embedded 程序 algorithm
是 ignored. 便条 那 一个
硬件 重置
立即 terminates 这 程序
-
ming 运作. 这 程序 command sequence 应当 是 reinitiated once 这
设备 有 重置 至 读 排列 数据, 至 确保 数据 integrity.
程序编制 是 允许 在 任何 sequence 和 横过 sector boundaries. 程序-
ming 至 这 一样 地址 多样的 时间 没有 intervening erases 是 限制.
为 此类 应用 (所需的)东西, 请 联系 your local spansion represen
-
tative.
任何 位 在 一个 文字 或者 字节
不能 是 编写程序 从 “0” 后面的 至 一个
“1”.
attempting 至 做 所以 将 halt 这 运作 和 设置 dq5 至 “1,” 或者 导致 这
data# polling algorithm 至 表明 这 运作 是 successful. 不管怎样, 一个 suc
-